Pos	Machineries & Equipment	Serial Number	Capacity & Quality	Location	Remark's
RB-001	Smoke Stock	Fabricated		Outside the mill
RB-002	Reheating Furnace	Fabricated	45 tons of billets per hour capacity, bunked fuel oil tiped, pre-heat and seeking, section, mild steel plate welded construction, size 21.0 meters long x 7.9 width x 3.0 meters high over all dimension, insulated with refectories, such as thermal ceramic. Coastal casts, firebricks, mineral wool ceramic, skamolex calcium silicate board, complete with 14 burners and other standard accesories.	Inside the mill
RB-003	Induced Draft Fan	767-M	Robinson Industries Inc. Type RL, 32,300 cu. M. per hr. capacity, Sized 200-20 driven by 149 kw electric motor 450/223 volts, 3-phase, 60 hz, complete with control and other standard accessoires.	Inside the mill
RB-004	No. 1 Mdl Approach Table		Heavy steel construction frame, 19.83, meters long, 191 mm. Dia. X 1057 mm Wide chain and sprocket drien by 4-3.73 kw gear motor, 1800 rpm, 440 volts, 3-phase, 60 trz, equipped with
RB-005	Run Back Table		Heavy steel construction frame, 13-roller high, size 191 mm dia x 908 mm, wide driven by 3,73 kw electric motor, complete with pneumatic kick off
RB-006	Roughing Mill No.1		Birdsboro No. Y985A single stand, 3-roller high, Size 470mm dia x 1524 mm wide 53,6 rpm, water cooled, mechanical and hydraulic roll balance, manual adjustment.
RB-007	Roughing Mill No.2		Birdsboro single stand 3-roller high Size 470mm dia x 1524 mm wide 79,3 rpm, water cooled, mechanical and hydraulic roll balance, manual adjustment.
RB-008	Signation Reducer Pinion Stand No.1		Western Gear, Order No. 17035, 4.8.1 ratic, 1200 hp input, water cooled, splash and spray lubrication system equipped with.
RB-009	Heaf Exchanger	55885	Young Radiator Co., Model 1 8566, 360 h temperature
RB-010	Lube Oil Pump		Gear type, 83 mm, dia discharge, coupled to:	Rapping Mill No.1
RB-011	Signation Reducer Pinion Stand No.2	55942	Western Gear, Order No. 17035, 4.8.1 ratic, 1200 hp input, water cooled, splash and spray lubrication system equipped with.
RB-012	Lube Oil Pump		Gear Type, 63 mm dia dischange, coupled to:		R. No.2
RB-013	No. 2 Mill Approach Table		Heavy steel construction frame, 15:25 meters long, 12 rollers, 191mm, dia x 1067mm wide chain and spocket driven by 3-3.73 kw gear motor, 1800 rpm, 440 volts, 3-phase, 60 hz, equipped with:	Middle Area
RB-014	Run Back Table		Heavy steel construction frame, 11 rollers, 191mm dia x 508 mm wide, driven by 3.73 kw electric motor, complete with pneumatic kick off
RB-015	3-Pneumatic Bar Tumers		1 ton capability, pneumatic achuaried
RB-016	Hydraulic Lift Table		Heavy steel frame construction, 5 tons capacity 10.06 meters long, 7 rollers, 203mm dia x 279 mm wide, hydraulic and mechanically actuated, driven by DC Gear Motor, 3-2.23 kw and 2-15 kw
RB-017	Table Transfer Table (Run-in)		Heavy frame construction, 23.49 meters long 19 rollers, 610 mm dia x 381 mm wide
RB-018	2-Gear Drive, 11.19 kw DC Motor	YP502A 283959	General Electric, Type MD-604AE, Model 288859, 725 rpm, 230 volts
RB-019	Transfer Table		Structural steel frame 29.32 meters length x 13:20 meters width with pulley drive / with motor TV-7265656 (RB-019-A)	Parts located at Looping Mil Areas	uninstall
RB-020	Transfer Table Conveyon (Run-out) In No. 2		Heavy steel frame construction, 13:20 meters long, 16 rollers, 510 mm dia x 381 mm wide
RB-021	2-Gear Drive, 11.19 kw DC Motor	259950	General Electric, Type MD-604AE, Model 288859, 725 rpm, 230 volts/with separate motor A serial no. 7265650 and B 72665667		Uninstall
RB-022	5.5 kw Electric Motor, General Electric Thru Gear Reduce	218B959	Cleveland Gear, 200AT Size, 26F Series 6-4/5.1 ratio, 720 rpm / install with 11:19 kw DC motor serial no.28B959